how to unlock livebox 2 orange

The Livebox 2.0 is manufactured by Sagem router that offers greater possibilities than FTTH or 3G connections, SIP telephony, digital television, the hotspot function, WDS and much more. However, with the Orange firmware all these features are disabled to the point that even can be configured with the connection settings of any other operator.

Step by step video tutorial teaching you how to unlock the livebox 2 sagem using free tools.

how to unlock livebox 2 orange part 1

how to unlock livebox 2 orange part 2

how to unlock livebox 2 orange part 3

how to unlock livebox 2 orange part 4

 facebook Page

Release so it can be used with ADSL or FTTH operator activarle functions not possible with the steps below, but not all at the moment and as long as no one has used the Orange connections, since in this case will be automatically updated and locked. Steps 1, 2 and 3 are required if the firmware version is higher than the 69127A, which is normal if the router was used.

 PREREQUISITES

- Download and unzip the following link Unlock Livebox 2.rar folder in C :, where you will find all the commands and programs for use with administrative user: 

MediaFire : Here
Mega.nz : Here
- Manually configure the network connection cable with 192.168.1.10 IP, mask 255.255.255.0 and the gateway 192.168.1.1.
- Turn off Windows firewall, connect the network cable strictly after the restart.

1. rescue mode TURN ROUTER

In this mode, the router firmware starts with a "rescue" (ARM) can replace the main firmware or changing an internal configuration provided you have the password for telnet access (user: root, password password 1234 versions of MRA or below the 69223E).
- For this boot the router with the reset button back to the light from a blue LED, which indicates that he is in charge of a particular firmware image.
- Access to the router http://192.168.1.1 and check the version of "rescue" shows that if it is not more than the FAST3yyy_MRA_69223E can skip to step 3.

2a. A CHANGE ARM version that allows root access

- In the subfolder folder and press dhcpsrv dhcpsrv.exe run in this order: Service / Installation exceptions firewall / Set and Service / Start.
- Back to the main mode SW rescue router and access to confirm that the version recorded FAST3yyy_MRA_69223E.
- Stop dhcpsrv in its setup screen, remove the exception of firewall, remove the service and exit dhcpsrv.
If confirmed the new version of the ARM and you can proceed to Step 3, but to leave permanently etched can do the following.

2b. Save firm root access FOR ARM

Tftpd32.exe to run tftpd a subfolder.
- Run and press again to dhcpsrv.exe: Service / Installation exceptions firewall / Configure, Service / Start.
- In this folder, open the program and telnet 192.168.1.1 putty.exe connection.
- In the new window to connect to the router with the user: root, password: 1234.
- Paste the following command:
loadapp app1 192.168.1.10 FAST3yyy_MRA_69223E.img.sz

- Stop dhcpsrv in its setup screen, remove the exception of firewall, remove the service and exit dhcpsrv.
This will write the flash device file version of the ARM 69223E well all beginning to make in the "rescue" has root access.

3. CHANGE REQUIRES FIRMWARE 69127A

 

 Maintain tftpd tftpd32.exe open subfolder.
- With your putty.exe implementation subfolder, telnet window to IP 192.168.1.1 with the user: root and password: 1234 and the write command: LOAD

- Start the process of writing to the flash memory of the router during which both the telnet window as progress bars TFTPD32 exposure window.
- Reset the router normally be accessed to verify that begins with the 69127A and firmware via user name and web administration password to reset the menu and Yuda Support -> reset.

4. Edit user permissions

  

- From a MS-DOS screen (Start / Run / CMD), type:

telnet 192.168.1.1
login: LBV2techno
password: 1901b95ae4295d613abf9eabae0b9d40

rg_conf_set /admin/user/0/permissions/superuser 1
rg_conf_set /admin/user/1/permissions/superuser 1
rg_conf_set /admin/user/2/permissions/superuser 0
save
reconf 1
reboot

This will help future opportunities can be accessed with all permissions (root) to the router with the username and password admin / admin (0 user) or root / 1234 (1 user). Also limited the capacity LBV2techno user (User 2), which limits to Orange to put the remote firmware and cancel all the changes that are going to do next.

5. Enable HID menus

- To allow some hidden menus in the router's web menu, enter the following command from the MS-DOS screen:

telnet 192.168.1.1
login: "admin" ou "root"
password: "admin" ou"1234"

rg_conf_set wbm/settings/pages/hsiab 1
rg_conf_set wbm/settings/pages/livezoom 1
rg_conf_set wbm/settings/pages/visio 1
rg_conf_set wbm/settings/pages/community 1
rg_conf_set wbm/settings/pages/fax 1
rg_conf_set wbm/settings/pages/telephone 1
rg_conf_set wbm/settings/pages/tv 1
rg_conf_set wbm/settings/pages/vpn 0
rg_conf_set wbm/settings/pages/backuprestore 1
rg_conf_set wbm/settings/pages/licence 1
rg_conf_set wbm/settings/pages/log 1
rg_conf_set wbm/settings/pages/lockunlock 1
rg_conf_set wbm/settings/network/ftth 1
rg_conf_set wbm/settings/network/adsl 1
rg_conf_set wbm/settings/network/3g 1
rg_conf_set wbm/settings/network/pppoe 1
rg_conf_set wbm/settings/network/pppoa 1
rg_conf_set wbm/settings/network/dhcp 1
rg_conf_set wbm/settings/network/ftlock 1
rg_conf_set wbm/settings/network/h323 1
rg_conf_set wbm/settings/network/sip 1
rg_conf_set wbm/settings/network/tvrouted 1
rg_conf_set wbm/settings/services/rtcphone 1
rg_conf_set wbm/settings/services/universal_phone 1
rg_conf_set wbm/settings/services/multitv 1
rg_conf_set wbm/settings/services/professionnal 1
rg_conf_set wbm/settings/services/residential 1
rg_conf_set wbm/settings/services/testvoip 1
rg_conf_set wbm/settings/services/wifipushbutton 1
rg_conf_set wbm/settings/services/wifiwps 1
rg_conf_set wbm/settings/services/wpspushbutton 1
rg_conf_set wbm/settings/services/msgwaiting 1
rg_conf_set wbm/settings/test/fmdev 1
rg_conf_set wbm/settings/test/sipdev 1

save

reconf 1

 It will be a menu like this:

6. Change ADSL settings

 - To configure the router with the parameters of any DSL provider, introducing them with the following commands:

telnet 192.168.1.1
login: "admin" ou "root"
password: "admin" ou "1234" 

 

rg_conf_set /dev/ethoa6/atm/pvc/0/vci xx
rg_conf_set /dev/ethoa6/atm/pvc/0/vpi xx

rg_conf_set /dev/ppp0/username xxxxxxxxxxxxxx

rg_conf_set_obscure /dev/ppp0/password xxxxxxx

save
reconf 1
reboot